新足迹

 找回密码
 注册

精华好帖回顾

· 瀚宝,相信你今后会比我们过得更好! (2008-8-2) UEJ · ********************糖醋熏小黄鱼,带子沙拉,花菜虾仁************ (2011-11-29) chesecake
· 从猥琐男到美少年--非专业的Schnauzer Grooming(多图慎入) (2011-11-28) 胡须康 · 把炒菜当艺术品来弄 - 东坡肉 (2009-8-30) 老陶
Advertisement
Advertisement
查看: 3581|回复: 2

[修房建房] DIY瓷砖 [复制链接]

发表于 2017-12-4 21:46 |显示全部楼层
此文章由 阳光海岸 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 阳光海岸 所有!转贴必须注明作者、出处和本声明,并保持内容完整
本帖最后由 阳光海岸 于 2017-12-4 21:51 编辑




澳村这家店提供免费的瓷砖设计软件,现在村里的瓷砖店和国内一样终于可以先看效果图再购买瓷砖了。

http://www.beaumont-tiles.com.au/

转贴DIY注意事项:专业大叔,大婶请补充细节
The Top 10 Reasons for Tile Fixing Failures:

1. Incorrect or no expansion joints: failure to use the correct expansion joints and tiling over construction joints will make your tiles too rigid, and they will crack during movement or expansion and contraction of the building.

2. Incorrect choice of adhesive. This is one of the most common causes of tile fixing failure that we see. See our page on Adhesives and Grout for more information.

3. Adhesive skins before tile is bedded in. Do not allow your adhesive to dry before fixing the tiles.

4. Contaminated background. Ensure that the surface and area that you are tiling is properly cleaned before commencing tiling.

5. Poor or incorrect surface preparation.

6. Poor adhesive coverage. This can result from not using the correct notched trowel, using the spot fixing method, or allowing voids behind the tiles.

7. Unsatisfactory bed thickness. Ensure that you use the correct notched trowel when applying adhesive.

8. Excessive movement in the substrate.

9. Dust or loose backwash not removed from the backs of tiles. Ensure that you clean and dry the backs of tiles before laying.

10. Incorrect mixing ratio of adhesive powder and liquid. Always follow the manufacturer's directions, and always add the adhesive to the water to ensure a smooth mixture.

评分

参与人数 1积分 +10 收起 理由
商务车 + 10

查看全部评分

诚信做人,已诚求成。
Advertisement
Advertisement

发表于 2017-12-4 21:47 |显示全部楼层
此文章由 阳光海岸 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 阳光海岸 所有!转贴必须注明作者、出处和本声明,并保持内容完整
14 Golden Rules
1. Tiles must be dry and the back of the tile clean.

2. The surface being tiled should be true and even and free from grease, wax, oil, curing compounds, and all forms of contamination.

3. Adhesive should be applied using the appropriate notched trowel. Do not use the spot fixing method, and always apply adhesive horizontally with a notched trowel, rather than in a swirling motion.

4. The whole back of each tile must be in good contact with the adhesive. Press tiles firmly into the adhesive bed and ensure that no voids occurs beneath tiles. See rule 5...

5. Every now and then, lift a tile from the adhesive to check that complete contact with the adhesive is being made.

6. No not fix tiles over skinned adhesive.

7. Allow the adhesive to set before grouting: usually no less than 24 hours. During this time the tiles must be protected from potentially harmful factors like weather and water penetration.

8. Adhesives must be used strictly in accordance with the manufacturer's instructions.

9. To achieve greater adhesion and a longer open time, porous concrete should be dampened with water prior to tiling with cement based adhesives.

10. Any loose powder on the backs of tiles should be removed.

11. Appropriate movement joints must be used and construction joints must not be tiled over. See DIY Fact Sheet Wall and Floor Surfaces for more details.

12. For thin bed fixing of tiles, the minimum finished thickness of the adhesive should not be less than 3mm.

13. Hairline cracks of up to 2mm in concrete should be bridged. Clean and prime the surface, allow to dry, and apply a liberal coat of ABA Barrierflex as a one-to-one mixture. Inbed a reinforcement mat and immediately apply a second coat of Barrierflex. Allow to cure before tiling.

14. Tiles must never be stored in direct sunlight prior to fixing.
诚信做人,已诚求成。

发表于 2017-12-5 12:09 来自手机 |显示全部楼层
此文章由 yacon 原创或转贴,不代表本站立场和观点,版权归 oursteps.com.au 和作者 yacon 所有!转贴必须注明作者、出处和本声明,并保持内容完整
收藏了

发表回复

您需要登录后才可以回帖 登录 | 注册

本版积分规则

Advertisement
Advertisement
返回顶部